Rancang Bangun Quadcopter Untuk Foto Udara
Abstract
Unmanned aerial vehicle (UAV) technology with remote control has developed rapidly in facilitating needs, especially in the field of photography. One type of UAV that is widely made or developed is the quadcopter. Taking aerial photos, for example, for survey, mapping, agriculture and spatial use can be done by utilizing the quadcopter. This study aims to design and determine the performance of the quadcopter for aerial photography purposes. From the results of the research, a quadcopter has been developed with a total lift capability of 15.8 newtons, an average flight time of 9.6 minutes when testing with a full battery condition up to 11.1 volts, namely the time to carry out aerial photo missions and 20.04 minutes from condition of the battery is full until the voltage on the battery is empty.
Keywords
References
Fernando, E., & Touriono, D. (2017). Rancang Model Frame Multicopter: Literature Review. Jurnal Processor, vol 11(2), hal: 861-870.
Giancoli, Douglas C. (2001). Fisika Edisi Kelima Jilid 1. Penerbit Erlangga. Jakarta.
Hidayat, R. (2019). Rancang Bangun Prototype Drone Penyemprot Pestisida Untuk Pertanian Padi Secara Otomatis. Jurnal TEKTRO, 3(2).
Indrawan, K. S., Hadary. F., & Hartoyo, A., (2018). Rancang Bangun Quadcopter Obstacle Avoidance Untuk Navigasi Dalam Ruangan Dengan Menggunakan Sensor Ultrasonik Srf-05. Fakultas Teknik, Universitas Tanjungpura. Pontianak.
Javir, A. V., Pawar, K., Dhudum, S., Patale, N., & Patil, S. (2015). Design, analysis and fabrication of quadcopter. Journal of Advance Research in Mechanical & Civil Engineering (ISSN: 2208-2379), vol 2(3), hal: 16-27.
Kuantama, E., Craciun, D., & Tarca, R. (2016). Quadcopter body frame model and analysis. Ann. Univ. Oradea, 71-74.
Lacey, S., Mancuso, S., & McKenzie, B. (2021). DJI Drone Modification. Department of Mechanical Engineering, University of Akron. USA.
Miftah, I. (2015). Rancang Bangun Pesawat UAV Hexacopter Dengan Kendali PID (Doctoral dissertation, Institut Teknologi Sepuluh Nopember).
Prakoso, T. B. (2015). Implementasi Dji Naza M-Lite Pada Quadcopter. Jurnal Mikrotek, vol 1(4), hal: 192-197.
Raydina, H. H., (2019). Rancang Bangun self-Awear Drone. Fakultas Teknik Universitas Negeri Semarang. Semarang.
Rizaldi, Rizki, Seno Darmawan Panjaitan, and Muhammad Saleh. (2021). Analisis Unjuk Kerja Unmanned Aerial Vehicle (Uav) Hexacopter Pada Lahan Pertanian. Jurnal Teknik Elektro Universitas Tanjungpura 2.1.
Saputra, D. R. H., & Pramujati, B. (2013). Rancang Bangun Prototype Unmanned Aerial Vehicle (UAV) dengan Tiga Rotor. Jurnal Teknik ITS, vol 2(1), hal: B47-B52.
Tatale, O., Anekar, N., Phatak, S., & Sarkale, S. (2018). Quadcopter: design, construction and testing. International Journal for Research in Engineering Application & Management, vol 4, hal: 1-7.
Theys, B., Dimitriadis, G., Hendrick, P., & De Schutter, J. (2016). Influence of propeller configuration on propulsion system efficiency of multi-rotor unmanned aerial vehicles. In 2016 international conference on unmanned aircraft system (ICUAS) pp. (195-201).
Utama, M. R. W., Komarudin, M., & Trisanto, A. (2013). Sistem Kendali Holding Position Pada Quadcopter Berbasis Mikrokontroler Atmega 328p. electrician, vol 7(1), hal 34-46.
Utomo, B. J., & Siregar, S. (2015). Rancang Bangun UAV (Unmanned Aerial Vehicle) Model Quadcopter dengan menggunakan Algoritma Proportional Integral Derivative. Proceedings of Applied science, vol 1(1).
Wicaksono, B. C., (2019). Pengaruh Penggunaan Fender Frame Drone dan Beban Terhadap Konsumsi Arus Baterai. Fakultas Teknik, Universitas Negri Semarang. Semarang.
Refbacks
- There are currently no refbacks.
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
Penerbit:
Jurnal Teknologi Rekayasa Teknik Mesin diterbitkan oleh Jurusan Teknik Mesin Fakultas Teknik Universitas Tanjungpura Pontianak
e-ISSN : 2798-0421